• Join the 2026 Outdoor Living Foundations Dealer Program. Sign Up now

Xtreme Jointing Compound

GftK vdw 850 Plus

Xtreme Jointing Compound is a 2-component epoxy paving joint compound designed for large format natural stone, concrete paver surfaces, and other high-traffic areas – both residential and commercial.

Order Online
become A Dealer
xtreme plus vdw 850
dutchies stone work llc hardscape installation in kennett square pa 3 1
custom patio and walkway hardscape installation in west chester pa

Why Use The Xtreme Jointing Compound VDW 850 Plus?

pressure washer vdw 850

Pressure Washer Friendly

Easily Cleanable!
Epoxy Mortar is known for its exceptional strength and durability. It forms a robust and resilient bond between tiles, providing superior resistance to cracking, staining, and other forms of damage. It can withstand anything from heavy foot traffic and moisture to UV exposure and chemicals. With this joint mortar, your tile will stand the test of time.

water permeable for vdw 850

Water Permeable

Being permeable means that water will flow through the compound. This is especially important to have in freezing and thawing climates. This keeps the stones dry while reducing water runoff from rain or irrigation systems which allows water to drain into the ground. This water then soaks into the earth, which recharges our groundwater and slows erosion.

self compacting for vdw 850

Self-Compacting

With any Joint Compound, having it be self-compacting allows for increased strength by minimizing voids between pavers. This creates a tighter bond and seal!
With this feature, there is no need for additional compacting equipment during installation.

applicable in low temperatures vdw 850

Applicable in Rain And Low Temperatures

Outdoor tile installations can accumulate dirt, stains, and other debris over time, especially in high-traffic areas. Epoxy mortar is easy to clean and maintain, making it an excellent choice for outdoor use. Consistent cleaning can keep your outdoor space looking fresh and sharp for years to come..

xtreme plus vdw 850

Technical Product Data

Product SizeComes in a 55 lb bucket
Application TimeApprox. 30 minutes at 20°C | 68°F* application temp. *Quick hardening at higher temperatures, and slow hardening at lower temperatures.
Compressive Strength33.1 N/mm / 4800 psi
E-Modulus5500 N/mm
Water PermeabilityApprox. 0.075 gal/min/sq. ft. for a joint fraction of 5%
Application Temp.2-26°C | 37-80°F (Do not lay onto frozen ground.)
Flexural Strength 10.3 N/mm / 1494 psi
Dry DensitySet mortar density: 1.62 g/cm3
Storage Life1 year if stored unopened in sealed and undamaged packaging. Must also be kept dry and frost-free. Do not store at temperatures above 20°C / 68°F
Download the full spec sheet

Recommended Mixing Tools:
X055 Double Paddle Mixer

This Dual Paddle Mixer Offers the Highest quality materials and the finest German engineering. It’s the most reliable product on the construction site. Proven hundreds of thousands of times on job sites all over the world.

Learn More
Buy Now

Recommended Application Tools:
Brooms and Squeegee Bundle

The 3-Piece Brooms & Squeegee Bundle is all the tools you need for clean and easy 3-part installation of any 2-part Epoxy all in one place.
Suitable for all GftK products except VDW 480 and VDW 495

Learn More
Buy Now

Application Instructions for Xtreme Jointing compound (VDW 850 Plus)

1

Construction Site Requirements

  • A stable, load-bearing structure, water-permeable sub-base, and the bedding layer – we recommend the PHNA Xtreme Trass Bedding Compound (vdw 480) – must all be correctly designed and installed for the anticipated traffic loads and in accordance with ASTM.
  • The PHNA Xtreme jointing compound is designed for small up to large format and cannot be used to compensate any settlement of the substructure, or for the sealing and waterproofing of any surfaces. Movement joints must be installed as necessary to comply with the required structural design and any anticipated levels of movement.
  • The PHNA Xtreme jointing compound can be applied on damp / wet paving and in high humidity and even in the rain.

2

Preparation

Preparation / Pre-wetting:

  1. Clean the surface thoroughly of all dirt, cement residues, organic materials or any other possible
    contaminants including cleaning out all of the joints to the required depth. We recommend a pre-treatment with the PHNA Xtreme Stone Protect 3-in-1 (vdw 950) for any porous and/or sensitive paving surfaces – please allow at least 24 hours after application prior to grouting.
  2. Thoroughly pre-wet the surface of the paving and mask adjacent surfaces which are not to be jointed. Always use clean and fresh tap water!

3

Mixing & Filling the Joints

  • Open your bucket of PHNA Xtreme jointing compound and remove the separate bottle of liquid hardener, then set it aside. Using an appropriate dual- or single-paddle drill mixer, pre-mix the aggregate for a minimum of 30 seconds, then add the hardener and mix for a minimum of 3 minutes until the mixture is smooth and
    homogeneous.
  • Proper mixing is important! Any material that is not thoroughly mixed must not be used. No water should be added during the mixing process.
  • Apply immediately after mixing, by pouring the PHNA Xtreme jointing compound directly onto the pre-wetted surface. Work the self-compacting material thoroughly into the joints using a rubber squeegee and/or stiff broom. If the viscosity of the product diminishes re-moisten by spraying lightly with water from a hose.
  • The paved area must be kept constantly wet during application. We recommend working from the highest to the lowest points. Do not mix partial units of the product. Any unmixed material must not be used.
  • All tools and shoes should be regularly cleaned with water.

4

Cleaning Off

  • Remove any excess PHNA Xtreme jointing compound residue from the area within 5 minutes (immediately at temperatures over 20 °C / 68 °F) by spraying lightly with water from a hose. You will notice a white film being washed away.
  • Avoid washing material out of the joints. Be careful to clean the paved surface towards areas not yet jointed and do not allow any water-containing residues to pond, stand, or dry out on the completed areas.
  • Finally, remove any remaining fine residues with a damp coconut fiber brush – do not brush any residual dry material into any unfilled joints. Clean this brush in water frequently.

5

Important Information

  • Remain off the freshly applied areas for a period of min. 24 hours, or until the paving surface is no longer tacky. Then the areas can be walked over.
  • The area can be fully released to vehicular traffic after 3 – 5 days, when fully hardened. In general, a strength test should be carried out before final clearance of the area.
  • A very thin film of the resin binder may remain on rough surfaces or any surfaces that are not cleaned thoroughly. This film will disappear after a period of exposure to traffic and weathering.
Order Now
Become A Dealer

GFTK Consumption Calculator

Use This GFTK calculator to find out how much product you need!



Please Note For The Calculator:
Calculations will only occur if all fields are filled in correctly.
Please ensure that a 0. is listed where the dimensions are under an inch.

For The Xtreme Elutriant: 
Coverage is approximately 75 sq ft per bag of VDW 495.
Please View This PDF for Additional Information